For more easy and stress free DIY projects, head to Lowes. Before you put the cover plate back on, you’re gonna want to make sure your switch works so turn your circuit breaker on and…flip the switch…Victory!Īnd that’s all there is to it. Now all you have to do is attach the switch back to the box using the two long screws. Once all your wires are in place, it’s always a good idea to wrap some electrical tape around the screws and wires for extra insulation. Just wrap it on around the screw and tighten it up. Same thing goes for the copper ground wire. Connect the two hot black wires to the screws the same way that you took them off, you’re gonna want to put them right back on. To replace a three-way switch, follow these steps: Turn off the power to the switch at the circuit or fuse panel. So now we are ready to install our shiny new switch and I know it seems simple, but remember to make sure it is facing the right way…Up. Use a small screw driver and press it on in to pull the wires out. Some times these wires are attached using push in connectors. Now if you flip your switch over, a lot of times you’ll see a copper wire attached to a green screw and that’s actually your grounding wire, loosen that one up too. So we’re ready to disconnect our old switch now and what you wanna do is just pull it away from the wall, find your two hot black wires, and unscrew the copper ends to loosen up the screws. If it doesn’t beep, you’re ok to continue. You hold it on up to the wires to make sure there is no power flowing through here. You want to gently pull your switch out of the wall and this is where you use your circuit tester. Now we need to get to the wires so we can test them to make sure the power is actually off so we have to remove the switch from the wall and you can use a Phillips head for that. Take it off and right here you see your switch. Now first off, we’re gonna start by loosening the screws on the plate here so we can get to our switch. When you’re ready to get going, it’s always very important to turn your circuit breaker off and also label witch switch you are working with so no one turns it back on. Today we’re replacing the light switch that controls the light from only one location. Now before you call an electrician, let me show you how easy this job can be, and here’s how. Your light…doesn’t work, but all the other lights on the same circuit do. The key point in changing out a light switch is of course to turn off the circuit breaker. Anything electrical to me is scary, but she makes this look fun and easy so I will keep it in mind if I ever have an issue like this. This is a quick and easy fix you can try before having to call an electrician and forking out the money. Need to rewire a lamp? Check out How to Rewire a Lamp to find out how.In this video, Jackie from Lowe’s helps us to install a new light switch. You can install these switches as replacements for nearly any type of switch. Remove the screws that hold the switch in place, and pull the switch from the wall. If the tester doesn't light up, there's no power going to the switch. Remove the cover plate and test the terminals with the circuit tester. Sliding the toggle upward increases the light's intensity sliding it all the way down turns off the light. Shut off the power at the circuit-breaker box. Some dimmer switches are like toggle types. Dimmer switches, with a dial to control the brightness, turn the light off when the dial is turned all the way down or pushed in. Some switches are available with the extra feature of a built-in neon lamp that glows when the switch is off, making it easy to locate the switch in the dark. The push-button switch has a single button that turns the light on when pressed and off when pressed again. It turns the fixture on when someone pushes the top of the switch in. A variation of the traditional toggle switch is the lever-action switch, which lies almost flush with the wall. When the toggle switch is mounted properly, the words ON and OFF are upright on the toggle lever, and the light goes on when you flip the switch up. The single-pole toggle switch is still the most popular. Attach cover plate with screws you took out earlier, and replace circuit fuse or trip circuit breaker back on.Īll switches work on the same general principles, and you can usually choose a switch with features you like best.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |